CTAG Y AKWEL lanzan la Unidad Mixta de Investigación S2-ACCESS

Sorry, this entry is only available in European Spanish. For the sake of viewer convenience, the content is shown below in the alternative language. You may click the link to switch the active language.

AKWEL y CTAG lanzan la Unidad Mixta de Investigación S2-ACCESS, con el objetivo principal de investigar en torno a soluciones inteligentes sobre sistemas de acceso a vehículo, focalizándose en dos ámbitos de trabajo: digitalización e innovación; y sostenibilidad y reducción de emisiones de CO2.

Los resultados alcanzados tras la ejecución de esta Unidad Mixta, que se prolongará hasta 2025, permitirá afianzar y reforzar el desarrollo de actividades de I+D en Galicia, y adquirir un mayor grado de conocimiento en las tecnologías electrónicas a investigar, generando un importante valor añadido a ambas entidades.

La Unidad Mixta de Investigación S2-ACCESS está subvencionada por la Axencia Galega de Innovación, en el marco de la convocatoria “Axudas para a creación e posta en marcha de novas unidades mixtas de investigación” (DOG Nº 45, de 7 de marzo de 2022), con código de expediente IN853A 2022/02, y contando con el apoyo de la Vicepresidencia Primera y Consellería de Economía, Industria e Innovación.

 

CTAG leads the first public demonstration of autonomous driving supported by 5G technology on the border between Spain and Portugal

These tests have been carried out within the framework of the 5G-MOBIX European project, focused on 5G technology for advanced Connected and Automated Mobility. The demonstrations carried out reveal the impact of the solutions tested in various scenarios of a dynamic border route characterized by the low latency and the service continuity enabled by the 5G network.

At the Tui-Valença international bridge, with the 100% electric autonomous shuttle developed by CTAG, two main use cases were presented: speed adaptation, where the autonomous shuttle slows down or stops to avoid a pedestrian thanks to the information provided by the infrastructure and the 5G network; and remote driving in a critical situation, where the vehicle relinquishes control to an operator to drive remotely from the control centre.

CTAG’s tracks also hosted live tests within the framework of the 5G-MOBIX project. Specifically, tests were carried out where an autonomous vehicle, in transit alongside non-connected vehicles, receives, through 5G, information on the position of the vehicles in the main lanes (for example, on a motorway), predicts their trajectories and adapts the speed for a safe merging manoeuvre.

Other tests focused on updating maps in real time: when the autonomous vehicle receives information from the traffic management centre about road works; the vehicle onboard unit receives the information, compares it with its own map, and concludes that its internal map is out of date. At that moment, it prompts the driver to take control and begins to record the information captured by the sensors. Once the vehicle has cleared the road works, it continues its way, in autonomous mode, and the on-board unit sends the data recorded by the sensors, via 5G, to the ITS Centre, which processes everything and generates a new map in HD. This new map is sent by the 5G network to nearby vehicles so that they can clear the road works autonomously.

Nearly one hundred technicians and representatives of the different project partners attended the presentation of the results of the 5G-M project and the live tests.

For more information, please check the press release of the event.

CTAG organiza el evento “8 TECNOLOGÍAS CLAVE PARA LAS FÁBRICAS DEL FUTURO”

Sorry, this entry is only available in European Spanish. For the sake of viewer convenience, the content is shown below in the alternative language. You may click the link to switch the active language.

CTAG organiza el evento “8 TECNOLOGÍAS CLAVE PARA LAS FÁBRICAS DEL FUTURO”, que tendrá lugar el jueves 22 de septiembre de 11:00 a 14:00 CET, como jornada de cierre del proyecto MAINGAP – Manufactura Innovadora en la Eurorregión Galicia-Norte de Portugal. El objetivo es presentar los resultados alcanzados y dar a conocer las 8 tecnologías centrales del proyecto, sus ventajas y aplicaciones multisectoriales, contribuyendo a la toma de decisión sobre la incorporación de las misma en las fábricas: Realidad Aumentada; Realidad Virtual; Robótica Colaborativa, Fabricación Aditiva; Exoesqueletos; Simulación para Logística; Gestión de la Producción y Fabricación Digital.

El proyecto MAINGAP está cofinanciado por el Fondo Europeo de Desarrollo Regional (FEDER) a través del Programa Interreg V-A España-Portugal (POCTEP) 2014-2020. CTAG lidera este proyecto de transferencia y valorización de tecnologías 4.0 a pymes innovadoras de la Eurorregión, en colaboración con la Axencia Galega de Innovación (GAIN) – CIS Tecnoloxía e Deseño ,el Centro de Engenharia e Desenvolvimento (CEiiA) y la Universidade do Minho.

MAINGAP ha desarrollado sus actividades en torno a soluciones tecnológicas innovadoras que responden a los desafíos que supone avanzar hacia la Industria 4.0 y la digitalización en la Eurorregión Galicia-Norte de Portugal, tomando como punto de partida sectores de referencia como el sector automoción y el sector aeronáutico.

Las inscripciones deberán formalizarse antes del 20/09/2022 a las 12:00. Entrada libre hasta completar aforo.

Programa de la jornada

Inscripciones

Logos de Interreg y MAINGAP

An autonomous vehicle designed by CTAG performs its first public tests in Arteixo

This morning the first open to the public tests of CTAG’s last-mile autonomous vehicle took place in Arteixo. The town mayor and the neighbors have had the opportunity of being the first to enjoy a ride on the 100% electric Shuttle.

The tests took place throughout the morning from Sabón beach car park, showing the joint work that Arteixo town council and CTAG are doing and revealing the solutions that this connected vehicle brings to mobility and as a complement to other transport services.

 

CTAG promotes digital innovation in SMEs

I4MSCTAG continues to support SMEs and is now a Contact Point of I4MS (ICT Innovation for Manufacturing SMEs), the initiative promoted by the European Commission to foster digital innovation of manufacturing SMEs in Europe in order to boost their competitiveness in the digital era.

Our aim is to respond to the needs of SMEs in a way that maximises their capabilities and boosts their developments/products/processes/services. CTAG wants to contribute to the adaptation of European SMEs to the current challenges of digital transformation by promoting cooperation, informing about the latest market trends and facilitating access to funding opportunities.

CTAG, through its OPEN PILOT BOOSTER LAB, promotes and validates new projects to reach the market in the shortest possible time, offering technical advice with more than 100 professionals working in the area of Robotics, Artificial Intelligence, Big data Digital Twin, advanced processes, etc.

logo I4MS

CTAG asistirá al Foro Europeo de Robótica (ERF2022)

Sorry, this entry is only available in European Spanish. For the sake of viewer convenience, the content is shown below in the alternative language. You may click the link to switch the active language.

Representantes dForo Europeo de Robótica e CTAG visitarán la ciudad de Rotterdam para participar en el European Robotics Forum. Se trata de la reunión más influyente de la comunidad robótica y de la IA en Europa, en la que personal investigador, profesionales de la ingeniería y del sector empresarial debaten los temas de actualidad en la robótica europea. La edición de este año, primera en formato físico tras la crisis del COVID-19, tiene un enfoque especial en sostenibilidad.

CTAG busca conocer las últimas novedades del sector, potenciar el networking, así como compartir los resultados de proyectos en curso, como CELL-OS (en ZDMP), PREMAR (en EFPF), INTEX (EIT-M), SMARTFLEXCELL (EIT-M), AUTOPESCA, FACENDO 4.0, y los recién terminados TESTED2 (EUROBENCH) o QUALIS (MARKET 4.0). La actividad en Industria 4.0 es la más relacionada con el evento, lo que incluye sus tres líneas principales: la fábrica hiperflexible, la fábrica inteligente y la fábrica humana.

El evento se celebra los días 28, 29 y 30 de junio en Rotterdam (Países Bajos).

Más información sobre ERF2022 en:

https://erf2022.eu/

ERF2022

CTAG presenta en Stuttgart sus últimos avances en desarrollo, ensayo y validación para el sector automoción

Sorry, this entry is only available in European Spanish. For the sake of viewer convenience, the content is shown below in the alternative language. You may click the link to switch the active language.

CTAG participa estos días en Automotive Testing Expo, el evento de referencia en Europa sobre desarrollo, ensayo y validación para automoción. Este evento se celebra en Stuttgart (Alemania) entre los días 21 y 23 de junio y en esta edición contará con más de 400 expositores.

Podrás encontrarnos en el stand 1540 en el Hall 10, donde mostraremos nuestras competencias para validar equipamientos, sistemas y componentes de vehículo en nuestros diferentes laboratorios: climático, acústica y vibraciones, seguridad pasiva, fatiga y durabilidad, motor, EMC, HiL/SiL, simulador de conducción, etc. Presentaremos también nuestras pistas de prueba equipadas para el desarrollo y validación de ADAS/conducción automatizada.

Esta edición servirá además para mostrar todas las novedades del EV Lab, el nuevo laboratorio de CTAG para impulsar la investigación y el desarrollo en torno a nuevos sistemas de propulsión más sostenibles. Con este objetivo, participaremos también en The Battery Show Europe and Electric & Hybrid Vehicle Technology Expo. Será la primera exposición de CTAG en este evento, que se ha convertido en la referencia para la comunidad de fabricantes, investigadores, proveedores y especialistas en tecnologías avanzadas de baterías para vehículos eléctricos e híbridos.

El Battery Show se celebrará entre los días 28 y 30 de junio, también en Stuttgart. Te invitamos a visitarnos en el stand 6-A20 en el Hall 6.

CTAG participa en ITS European Congress en Toulouse

Sorry, this entry is only available in European Spanish. For the sake of viewer convenience, the content is shown below in the alternative language. You may click the link to switch the active language.

ITS European CongressCTAG participa en la decimocuarta edición del ITS European Congress, que se celebra en Toulouse (Francia) desde el 30 de mayo hasta el 1 de junio.

Estaremos en el stand número D15, presentando nuestras tecnologías y capacidades de desarrollo en movilidad conectada, cooperativa y automatizada (CCAM). Además, presentaremos nuestros avances en conducción autónoma y las últimas novedades de SISCOGA, un corredor permanente de más de 200 km de carreteras urbanas e interurbanas para la realización de pruebas con sistemas inteligentes de transporte.

El evento contará con una ponencia de Francisco Sánchez, director de la División de Electronica y Smart Mobility de CTAG, titulada “Disruptive Technologies for Last-Mile Autonomous Shuttles”, el martes 31 de mayo a las 11:45.

El ITS European Congress se celebra en el Centro de Conferencias MEETT de Toulouse, contando con instituciones y empresas de más de 40 países líderes en movilidad inteligente y digitalización del transporte.

Más información sobre la conferencia en la web del ITS European Congress.

CTAG shows its latest advances in C-V2X technologies together with the key players in the sector

C-V2X PlugtestsThe demonstration took place during the C-V2X Plugtests™, an event organized by the 5G Automotive Association (5GAA) and the European Telecommunications Standard Institute (ETSI) in Germany.

This event, held from March 28th to April 1st, brought together organisations, institutions and key companies in the C-V2X ecosystem for the certification and development of these technologies in the automotive industry.

The C-V2X Plugtests™ also included a workshop to discuss the future of C-V2X systems in the automotive sector, as an introduction to the demonstrations carried out by CTAG, Vodafone, Commsignia and Allbesmart.

CTAG’s demonstration highlighted its latest advances in the field of interoperability with 5G technology, a crucial technology for the development of intelligent transport systems. For the development of the scenarios, CTAG installed its communications unit (HMCU) both in the infrastructure (RSU) and in the vehicle (OBU). The use cases shown included Traffic Jams Warning, Road Works Warning, Hazard On The Road Warning, Time To Green and In-Vehicle Signage.

The objective of these tests has been to assess the level of interoperability and validate the understanding of the standards, concluding with a high success rate shown by a very positive level of interoperability between the many providers.

More information about C-V2X Plugtests™ at  https://5gaa.org/news/5gaa-partnered-with-etsi-and-dekra-to-showcase-c-v2x-interoperability-and-discuss-deployment-during-the-plugtests-at-the-dekra-automobil-test-center-in-klettwitz-germany/

CTAG participa en INTEX, una iniciativa para la creación de bancos de pruebas para exoesqueletos

Sorry, this entry is only available in European Spanish. For the sake of viewer convenience, the content is shown below in the alternative language. You may click the link to switch the active language.

prueba con exoesqueletosA través de la iniciativa InteX “Next Generation Al Based Testbeds for Wearable Robotics” creamos e implementamos bancos de pruebas instrumentados y modulares: se utilizan para simular el proceso de fabricación específico del cliente, así como para valorar el rendimiento del exoesqueleto en ciertas tareas. Los bancos de prueba permiten la medición cuantitativa del valor añadido de un exoesqueleto sin la necesidad de realizar pruebas in situ; que resultan costosas y consumen mucho tiempo en las instalaciones del fabricante.

Gracias a esta iniciativa, CTAG capitalizará los resultados del proyecto TestEd y la patente P201930911 “Sistema para la realización de pruebas de exoesqueletos en un entorno controlado”.

El uso de exoesqueletos es cada vez más creciente en el ámbito industrial. Mejora la ergonomía del puesto de trabajo y optimiza el sistema productivo. Sin embargo, antes de que las empresas puedan beneficiarse de las ventajas del uso de exoesqueletos, es necesario validar previamente que están preparados para las tareas específicas a realizar por parte del usuario final.

Por lo tanto, habrá que llevar a cabo una evaluación previa y exhaustiva de múltiples factores, así como la evaluación del impacto en la introducción de exoesqueletos en los lugares de trabajo.

Nuestras plataformas están diseñadas para evaluar y mejorar la seguridad, usabilidad y el rendimiento de los exoesqueletos, a la vez que ayudan a promover su adopción y aceptación, inspirando la confianza del usuario final.

Logo Intex

Intex es una iniciativa co-financiada por el EIT Manufacturing, en la que además de CTAG participan también Tecnalia, COMAU, IUVO, Acciona Construcción y la Universidad libre de Bruselas.

Logo EIT Manufacturing and UE